InfoControl -Radar Modules

PC Converter and Software
Program your building’s functionality

Features

	PC to bus converter	The interface between the InfoControl management software and the control modules it manages. Up to 256 modules can be managed by a single converter. Connected via RS232 cable to the PC COM port. Status LED’s for power supply, control bus and internal processor.

	Standalone	The PC bus converter will continue to function if the PC is inoperable for whatever reason.

	Audit trail	InfoControl management software provides an audit trail of all activities that have occurred. Temperature changes, movement, light etc. See at a glance not only when it changes but the values too!

Copyright notice: Website and content: Copyright 2001, 2002 InfoByte AG Microsoft is a trademark from Microsoft Incorporation InfoControl is a trademark from InfoByte AG. Technical specifications are subject to change without prior notice.

PC Converter and Software
Program your building’s functionality

Technical specifications

Electrical
connections

2,1mm external power source plug

Power source

48V Power supply

Power consumption

2,4W / 50mA

Environmental

Normal operating temperature: -10°C to +40°C. Relative humidity 90%

Connectors

Two RJ12 connectors for control bus

LED

2 x red LED for bus processor function check. 2 x green LED for power supply

Connectivity

• A single PC bus converter can manage and control a

maximum of 256 modules.
• A PC bus converter must be attached to its own dedicated

COM port on the PC.
• If more than 256 modules are installed, 2 or more additional

PC bus converters must be present, each connected to a

dedicated COM port on the PC.
• A PC bus converter can have a 1 or two strings attached.
• The maximum number of modules on a single string is 32.
• For example, a single converter with no repeaters, and two

strings attached, can have a max. of 64 modules

(32 on each string). The figure of 32 is derived from the max.

current consumption allowed on the string.
• Control bus cable distances also have an effect on the

maximum number of modules that can be connected. You

may require repeaters to be installed. (maximum length is 1

Km).
• If one or more repeaters are used, a string can be expanded

by a factor of 32 for each repeater, up to a maximum of 256.

Control bus
cable limits

The longer the segment is, the less modules can be attached due to electrical constraints. The table below indicates the maximum number of modules that can be attached relative to the length of the string or segment. Distances shown are in meters.

String length (m)	100	200	300	400	500	600	700	800	900	1000
Max. no modules	32	25	17	12	10	8	7	6	5	5

Copyright notice:
Website and content: Copyright 2001, 2002 InfoByte AG *Microsoft is a trademark from
Microsoft Incorporation *InfoControl is a trademark from InfoByte AG.

Technical specifications are subject to change without prior notice.

PC Converter and Software
Program your building’s functionality

A new way to perceive interactivity

The PC converter is your interface between the InfoControl management software and your intelligent modules. InfoControl management software stores all the information related to your installation in its database together with «instructions» on what to do and when. When you change a parameter, or describe an event to which the modules should react, this information is transmitted and stored in onboard microcomputer of each switchbox, sensor or module using the control bus.

If the PC is «down» for whatever reason the system remains fully programmed and continues to run using the stored information. In short, reliability and stability is guaranteed. Extensive logging capabilities provide you with a comprehensive audit trail of all the events that have taken place in your installation. InfoControl software is compatible with Microsoft Windows 95, 98, ME, NT, 2000 and XP. The PC to bus converter will handle up to 256 modules (switchboxes, sensor and wall switch). Each module has a specific hardware address.	Build your smart house with the world's easiest to use building control system. Each sensor and module has its own dedicated microcomputer onboard and can access internet and communication services. Time and distance becomes meaningless. You can control your building or house from anywhere in the world, receive emails, messages, alarms, notifications and many other types of information. Large Image

The converter is connected to your PC using an RS232 COM port. It connects your home or building to the PC and allows you to access it over Internet, send SMS, email and many other features. If an event occurs, InfoControl will let you know about it, should you choose to be notified. If you want to install more than 256 modules connected, you can add another converter (connected to another COM port). You can also install repeaters to increase distance or capacity. The connectivity parameters are described in the technical specifications overleaf. It is recommended that a UPS is installed to maintain power to the converter.
Copyright notice: Website and content: Copyright 2001, 2002 InfoByte AG Microsoft is a trademark from Microsoft Incorporation InfoControl is a trademark from InfoByte AG. Technical specifications are subject to change without prior notice.